{"product_id":"water-cooled-woodworking-bearings-router-engraving-rm2608247tr4sja7","title":"DIY Water-Cooled Motor 1.5KW ER11 Woodworking 220V 380V 4 Bearings for Router Engraving(1.5KW 220V)","description":"\u003cp\u003e\u003cspan\u003eMotors\u003cbr\u003eSize: 80x190mm (diameter of middle body: 80mm x length: 190mm)\u003cbr\u003eSpeed regulation mode: The speed can be changed by three-phase output inverter and adjusting the frequency of the inverter.\u003cbr\u003eCooling method: water cooling\u003cbr\u003ePower interface: Optional H20-4 pin waterproof air . The air plugs labeled '1', '2', '3', '4', '1', '2', '3' are connected to the inverter (U, V, W), 4 are connected to the inverter The device is grounded.\u003cbr\u003ePower: 1.5kw\u003cbr\u003eVoltage: 220v\u003cbr\u003eCurrent: 5A\u003cbr\u003eFrequency: 0-400Hz\u003cbr\u003eSpeed: 0-24000rpm\u003cbr\u003eRunout: less than 0.01mm\u003cbr\u003eDiameter (mm): 80\u003cbr\u003e4 fully sealed angular contact bearings\u003cbr\u003eChuck: ER11\u003cbr\u003eClamping tool diameter: 17mm, 6.5mm, 6.35mm, 6mm, 5.5mm, 5mm, 4.5mm, 4mm, 3.5mm, 3.175mm, 3mm, 2.5mm, 2mm, 1.5mm, 1mm (standard 6mm)\u003cbr\u003eWater-cooled ER11 chuck\u003cbr\u003eGrease lubrication\u003cbr\u003eMain purpose: used for wood, bamboo, ordinary PCB, PVC, PMMA, plastic, bamboo, two-color board (ABS) and other non-metallic carvings.\u003cbr\u003eThe working environment temperature of the is usually -10~40.\u003cbr\u003eBefore installing the first electric to rotate the head by hand, you should feel flexibility and no blockage.\u003cbr\u003eP4 fully sealed angular joint bearings can extend the life of the .\u003cbr\u003eThe longer the length, the greater the and the greater the power.\u003cbr\u003eCareful assembly makes the more precise.\u003cbr\u003eThe accuracy is 0.01mm, and the coaxial cable is less than 0.0025mm\u003cbr\u003e1. Our main shaft uses 4 bearings.\u003cbr\u003e2. Bearings are to high temperature and low heat\u003cbr\u003e3. The ball bearing has low friction, low noise and long service life.\u003cbr\u003eWhen the is stored and transported, the bearing condition inside the high-speed grease will change, and the customer should run it at low speed for 30 minutes. Then increase slowly at a speed of 3000 rpm, running for 20 minutes each time. The and inverter should work together. The specifications and parameter settings of the inverter match the parameters.\u003cbr\u003eTo connect the inverter main shaft, the three-phase inverter power cord should be welded to the 1 (U), 2 (V), 3 (W) pin, and the grounded pin 4. After turning on the power, observe whether the rotation axis always shows the direction. If it is inconsistent, turn it off immediately, and replace the two wires of the three-phase power supply connected to the inverter and the .\u003cbr\u003eBefore using the every day, it must run at low speed for 15-20 minutes. Clamp the cutter on the , the chuck nut, chuck, and cutter must be clean enough. The shank inserted into the chuck must be larger than 15mm.\u003cbr\u003eThe water-cooled must be used together with the water pump. Otherwise, the will quickly break.\u003cbr\u003eThe AC motor must be used together with the inverter. The power of the inverter needs to be equal to or greater than the power of the . Before use, please set the inverter parameters suitable for the . Otherwise, the and inverter will break immediately.\u003cbr\u003eWhen using the , the noise is different from before, so please stop the immediately. You need to replace the bearing.\u003cbr\u003eThe frequency power supply is connected to the rated voltage, and the frequency should be consistent with the technical parameters of the electric . The speed can be adjusted to change the frequency, and the voltage changes in proportion.\u003cbr\u003eDo not use the , apply compressed air to blow off the static coolant in the pipeline. To prevent rust, please the water hole. The should be oiled. Add anti-wave device and put it in a dry place.\u003cbr\u003eTo replace the bearing, some professional and technical personnel should be replaced. With special tools, the bearings should be cleaned thoroughly without removing the stator coil.\u003cbr\u003eThe frequency power supply is connected to the rated voltage, and the frequency should be consistent with the technical parameters of the electric . The speed can be adjusted to change the frequency, and the voltage changes in proportion.\u003cbr\u003eDo not use the , the should be oiled. Add anti-wave device and put it in a dry place.\u003cbr\u003eTo replace the bearing, some professional and technical personnel should be replaced. With special tools, the bearings should be cleaned thoroughly without removing the stator coil.\u003cbr\u003e==========\u003cbr\u003eCertification : none\u003cbr\u003eDrive : MOTOR\u003cbr\u003eOperating Speed : 24000RPM\u003cbr\u003eModel Number : JGD-80A-1.5KW\u003cbr\u003eApplication : Milling\u003cbr\u003eOperating Speed : 24000RPM\u003cbr\u003eApplication : Milling\u003cbr\u003eModel Number : JGD-80A-1.5KW\u003cbr\u003eDrive : Motor\u003cbr\u003eOrigin : Mainland \u003cbr\u003eCertification : NONE\u003cbr\u003eDiameter : 80MM\u003cbr\u003ePower : 1.5KW\u003cbr\u003eCurrent : 5A\u003cbr\u003eVoltage : 220V\/360V\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003eItem details\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eASIN : B0GMQ37SWX\u003c\/li\u003e\n\u003cli\u003eBrand Name : ETFDRBVU\u003c\/li\u003e\n\u003cli\u003eManufacturer : ETFDRBVU\u003c\/li\u003e\n\u003cli\u003eModel : ETFDRBVU\u003c\/li\u003e\n\u003cli\u003eModel Name : ETFDRBVU\u003c\/li\u003e\n\u003cli\u003ePart Number : ETFDRBVU\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"ETFDRBVU","offers":[{"title":"1.5KW 220V","offer_id":48686881308866,"sku":"RM2608247TR4SJA7","price":169.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0772\/5734\/3170\/files\/51B-JSYfClL._SL1500_a6bb80a2-62de-433c-9783-234ec1af0dad.jpg?v=1787796143","url":"https:\/\/briantoraris.com\/products\/water-cooled-woodworking-bearings-router-engraving-rm2608247tr4sja7","provider":"Briantoraris","version":"1.0","type":"link"}